|
BLEEDER SCREW COVERS (PAIR)
KU2013
|
|
|
|
|
|
CHROME FUEL SHUT OFF KNOB FOR HONDA SHADOWS/ VT750/ VT1100/ VTX1300
1-247
|
|
|
|
|
|
ISO WINGS PEGS CHROME - PAIR (Requires Bike Specific Adapters)
4452
|
|
|
|
|
|
ISO-GRIPS WITH CHROME ACCENT RING FITS MOST HONDA CRUISERS 94-UP (EXCEPT VTX & 750 SPIRIT)
6236
|
|
|
|
|
Nice looking/feeling grip. It's pretty easy to get the stock grips off, just split the rubber with an exacto and take the chrome cap and grommet off. Kury glue was dried up, so I used i minute epoxy as adhesive. Goes with all my other Kury stuff.
|
|
|
LARGE ISO-PEGS WITH CLEVIS AND 1-1/4" CLAMPS (PAIR)
8033
|
|
|
|
|
|
SMALL ISO-PEGS CHROME - PAIR (Requires Bike Specific Adapters)
7964
|
|
|
|
|
Finally done with the Kury additions, and this one was much needed. Good quality like all Kury stuff.
|
|
|
BANJO BOLT COVER (12MM)
KU2015
|
|
|
|
|
|
FUEL SHUT OFF VALVE PLATE COVER FOR HONDA VT 750 ACE/ AERO/ SPIRIT/ VT1100/ VT1300 FURY/INTERSTATE STATELINE/ SABRE/ VTX1300
55-301
|
|
|
|
|
|
FOOTPEG ADAPTERS (REAR-HONDAS / FRONT YAMAHA RAIDER)
8802
|
|
|
|
|
Needed for my rear Kury pegs. Good quality as usual.
|
|
|
FRONT FOOTPEG ADAPTERS (ALSO 1100 SABRE & SPIRIT REAR FOOTPEG ADAPTER)
8803
|
|
|
|
|
Got to have them for Kury products. Nice chrome finish.
|
|
|
|
FRONT FOOTPEG ADAPTERS (ALSO 1100 SABRE & SPIRIT REAR FOOTPEG ADAPTER)
8803
|
|
|
|
|
|
ISO-THROTTLE BOSS
6250
|
|
|
|
|
Looks great. No more hand cramps!
|
|
|
FRONT SWEPT BRAKE CALIPER COVER
PABLV54052
|
|
|
|
|
|
BRAKE & SHIFT PEDAL COVER
4029
|
|
|
|
|
Much better and substantial looking
|
|
|
CHROMED DRIVE SHAFT COVERS FOR VALKYRIE / AERO 750 & SPIRIT 750 C2
06-0640
|
|
|
|
|
Yes... finally covered that ugly, black driveshaft!
|
|
|
RUN-TURN-BRAKE CONTROLLER FOR METRIC CRUISERS
KU4710
|
|
|
|
|
Very important addition. Now I have running lights with red Kury covers on the back. Crimping the connectors was a PITA. Almost soldered the wires instead.
|
|
|
LICENSE PLATE FASTENER SET (4)
PADS190512
|
|
|
|
|
Nice little addition to the back end.
|
|
|
SHIFT PEG COVER (universal item-see description)
4036
|
|
|
|
|
Looks good, but I kind of disappointing for a KuryakYn product. The rubber pads start bulging and popping out on top and popping in on the bottom. I tried all the tricks like wrapping the naked shifter with some electrical tape, etc., but ended up being best with no tape. At least the top isn't popping out. Guess I'll keep it on to go with all my other Kury stuff.
|
|
|
VINTAGE WIDE PLAIN TWO PIECE TOURING SEAT FOR AERO 750 04-09
76521
|
|
|
|
|
|
|
VINTAGE WIDE PLAIN TWO PIECE TOURING SEAT FOR AERO 750 04-09
76521
|
|
|
|
|
|
UNIVERSAL DRIFTER JUMBO SLANT SADDLEBAGS
PA35010320
|
|
|
|
|
|
EASY BRACKETS FOR AERO 750
EAAROR2
|
|
|
|
|
Got these to replace my throw over bags. Now, I can take my seat off and show off the curves. Here's the problem: the brackets are a bitch to get on if the fender posts are not tightened just right. I tried spacing them with washers and ended up just having to pound them down. I wish I had went with ghost brackets.
|
|
|
CHROME LIGHT BAR 750 AERO
HL08V31MEG100
|
|
|
|
|
|
CHROME BACKREST WITH PAD (LOW) 750 AERO
HL08F75MEG100B
|
|
|
|
|
|
SWITCHBLADE 2-UP CLEAR WINDSHIELD 750 AERO/ACE DELUXE/ SABRE -QUICK RELEASE
N21103
|
|
|
|
|
|
FRONT DEEP DISH BEZELS WITH SMOKE LENSES AND AMBER 2 CIRCUIT BULBS (PAIR)
2270
|
|
|
|
|
|
SWITCHBLADE MOUNTING HARDWARE FOR HONDA VTX 1300 R/S/ 1100 SABRE/ 750 AERO/ 750 ACE
KIT-Q203
|
|
|
|
|
Great, low-profile mount. Don't overtighten the alan bolts or you'll pop the spider clamp. Torque to INCH pounds, not foot pounds!
|
|
|
LICENSE BACKING PLATE
CC19885
|
|
|
|
|
|
LICENSE PLATE FRAME
CC15954
|
|
|
|
|
Good cheap chrome cover without spending $50.
|
|
|
CHROME FRONT FENDER RAILS FOR HONDA VT750 AERO 04-UP
BI53433
|
|
|
|
|
